Ac Current Sensor

Search for Ac Current Sensor videos, reviews, deals | Watch Ac Current Sensor online & compare prices

Current Transformer, DROK 100A/100mA AC Current Transformers, Mini Clip-on Current Sensor, Split Core Amp Transformer Sensing Relay, Easy to Install CT without Power Off

 (Current Transformer, DROK 100A/100mA AC Current Transformers, Mini Clip-on Current Sensor, Split Core Amp Transformer Sensing Relay, Easy to Install CT without Power)
Parameters: Environment temperature: -40℃~+85℃ Relative humidity: never more than 90% when the temperature is 40℃ Working frequency: 50Hz~60Hz Insulation endurance grade: B grade (130℃) Insulation resistance: more than 1000MΩ normally Dielectric strength: can afford power frequency 1000V/1minute Flame resistance: Conform to UL94-Vo grade Internal resistance: 42Ω    Test linear range: 0-100A 10A      secondary output: 10MA 50A      secondary output: 50MA 100A    secondary output: 100MA Ratio is 1000: 1   Range of Application: 1. The current transformer is used for energy meter in special; AC 220v, the 380v power supply can both be applied. 2. When you fix the energy meter, you don't need to cut off the power if you use this product.   Precautions: 1. The CT primary should be connected in series with the test current loop, the secondary should be as work in the short-circuit state 2. The secondary circuit is not allowed open circuit, so please do not install a fuse. Package Including: 1x Current Transformer

Sperry Instruments VD6505 Adjustable Non-Contact Voltage Sensor, 12-1000 V AC

 (Sperry Instruments VD6505 Adjustable Non-Contact Voltage Sensor, 12-1000 V)
A non-contact voltage tester serves as a key component in any electrical toolkit, allowing the user to verify the presence of AC voltage prior to working on an electrical installation or during troubleshooting without requiring physical contact with live electrical conductors. Engineered to specifications required by professional electricians the Sperry Instruments VD6505 Adjustable Non-Contact Voltage Detector allows for sensitivity adjustments in multiple-wire applications when precision and safety are crucial. This unit features an adjustable sensitivity dial able to detect the presence of AC Voltage from as low as 12 V to up to 1000 V AC and provides both audible (beeping) and visual (360 degree flashing red light) indicators to alert the user of the presence of voltage. The fully insulated probe tip eliminates the risk of contacting live electrical wires while the patented battery check feature designed into the unit ensures tester and batteries are operating properly, virtually eliminating false negative readings. This unit features 250lb crush-rated impact resistant ABS housing with a protective rubber overmold to withstand tough worksite applications while the soft-grip contoured design ensures a positive user experience over long hours of repeated use. Applications inclu...

SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A

 (SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer)
Specification: Model: SCT-013-000 Type: Non-invasive current transformer Core Material: Ferrite Input Current: 0~100A AC Output Mode: 0~50mA Leading Wire in Length: 1m Turns Ratio: 1: 1800 Work Voltage: 660 v Resistance Grade: Grade B Max Sampling Resistance: 10 Ω Linearity: ±3% Accurancy: ±1% Work Frequency: 50-1 KHz Work Temperature: -25˚C ~ 70˚C Reference project: Open Energy Monitor Dielectric Strength: 6000V AC/1min Opening Size: 0.51 * 0.51inch / 13 x 13mm Two Form of Output: current output or voltage output (a burden resistor needed to add); Mechanical strength: opening and closing times, no less than 1000 times (20 ℃) High Quality and Safe: Meet the requirement of flame-retardant characteristics (UL94-V0) Applications: For AC motors, lighting equipment, air compressors and other current measurement,monitoring and protection. Package include: 2 PCS Split Core Current Transformer SCT-013-000 100% Satisfaction Guarantee: 12-Month Warranty; No satisfied ,Free reason for return; We could also resend you new one due to quality problem.

JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer for Arduino Raspberry pi

 (JANSANE SCT-013-000 100A Non-invasive AC Current Sensor Split-Core Clamp Current Transformer for Arduino Raspberry)
Specification Model: SCT-013-000 Type: Non-invasive current transformer Core Material: Ferrite Input Current: 0~100A AC Output Mode: 0~50mA Leading Wire in Length: 1m Turns Ratio: 1: 1800 Work Voltage: 660 v Resistance Grade: Grade B Max Sampling Resistance: 10 Ω Linearity: ±3% Accurancy: ±1% Work Frequency: 50-1 KHz Work Temperature: -25˚C ~ 70˚C Reference project: Open Energy Monitor Dielectric Strength: 6000V AC/1min Opening Size: 0.51 * 0.51inch / 13 x 13mm Two Form of Output: current output or voltage output (a burden resistor needed to add); Mechanical strength: opening and closing times, no less than 1000 times (20 ℃) High Quality and Safe: Meet the requirement of flame-retardant characteristics (UL94-V0) 100% Satisfaction Guarantee 12-Month Warranty; No satisfied ,Free reason for return; We could also resend you new one due to quality problem.

DFROBOT 50A Current Sensor(AC/DC)

 (DFROBOT 50A Current)
Introduction This is a breakout board for the fully integrated Hall Effect based linear ACS758 current sensor. The sensor gives precise current measurement for both AC and DC signals.The thickness of the copper conductor allows survival of the device at high overcurrent conditions. The ACS758 outputs an analog voltage output signal that varies linearly with sensed current. This current sensor enables you to monitor currents in your project every second for energy saving or circuit protecting purposes. Features - Arduino interface compatible - 120 kHz typical bandwidth - 3 μs output rise time in response to step input current - Output voltage proportional to AC or DC currents - Factory-trimmed for accuracy - Extremely stable output offset voltage - Nearly zero magnetic hysteresis - Total output error improvement through gain and offset trim over temperature - Monolithic Hall IC for high reliability - Ultra-low power loss: 100 μΩ internal conductor resistance Specifications -Operating Voltage(analog): 5V -Peak Measuring Voltage:3000V(AC),500V(DC) -Current Measuring Rang:-50~50A -Sensitivity:40 mV/A -Operating Temperature: -40~150°C -Dimension:34x34mm Shipping List •Sensor (1 unit) •Analog Sensor Cable (1 unit)

HiLetgo Analog Current Meter Sensor Module AC 0~5A Ammeter Sensor Board Based on TA12-100 for Arduino

 (HiLetgo Analog Current Meter Sensor Module AC 0~5A Ammeter Sensor Board Based on TA12-100 for)
Specification: Interface: 3PIN Power Supply: 5V Size: 30x 24x 1.6mm Weight: 25g Electrical characteristics: Transformation coefficient: 1000:1 Input current: 0--5A Output current: 0--5mA Sampling resistor: 200Ω Sampling voltage: 0--1V Working frequency: 20-20000Hz Working temperature: -55--85℃ Dielectric strength: 6KAC/1min Package Include: 1* Analog Current Meter Sensor Module Board If you need detail schematic, please contact us

AC Current Meter, DROK 80-300V 100A Digital Multimeter Voltmeter Ammeter, LCD Display Voltage Amperage Detector Volt Amp Tester Monitor Gauge Panel with Current Transformer CT

 (AC Current Meter, DROK 80-300V 100A Digital Multimeter Voltmeter Ammeter, LCD Display Voltage Amperage Detector Volt Amp Tester Monitor Gauge Panel with Current Transformer)
Parameters: Measuring range: AC 80.0-300V; AC 0-100.0A Measuring accuracy: 1% ± 2digits Voltage display: Yellow LCD Current display: Blue LCD Size: 70*39*40mm Wiring: Green terminal: Voltage input Blue terminal: Current transformer secondary input Note: Please passing the wire of the measuring circuit through the hole of transformer. Important: 1. Voltage input (yellow terminal) and current transformer secondary input (blue terminal) cannot be connected to be wrong, otherwise the instrument will be burned out. 2. It is only suitable for pure AC 50Hz-electric power supply. The meter will get permanent damage if you measure the square wave, dc-to-ac inverter output and modified sine wave. Package Includes: 1x Digital Voltage & Current Meter 1x Current Transformer

CTYRZCH SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer 100A

 (CTYRZCH SCT-013-000 Non-invasive AC Current Sensor Split Core Transformer)
Core material: ferrite Mechanical strength: opening and closing times, no less than 1000 times (20 C) Safety indicators: Dielectric strength 6000V AC/1min Meet UL94-V0 flame retardant properties Operating Temperature: -25 C ~ +70 C Applications: for AC motors, lighting equipment, air compressors and other current measurement,monitoring and protection. Package include: 1 x Split Core Current Transformer SCT-013-000

Gikfun DIY 5A Range AC Current Transformer Module for Arduino (Pack of 5pcs) EK1344x5

 (Gikfun DIY 5A Range AC Current Transformer Module for Arduino (Pack of 5pcs))
5pcs DIY 5A Range AC Current Transformer Module Current Sensor Module for Arduino

AC Delco 213-912 Throttle Position Sensor

Ac Current Sensor (AC Delco 213-912 Throttle Position)

AC Delco 213-1520 MAP Sensor

Ac Current Sensor (AC Delco 213-1520 MAP Sensor)

AC Delco 213-1557 Camshaft Position Sensor

Ac Current Sensor (AC Delco 213-1557 Camshaft Position)
Shopping Results for "Ac Current Sensor"

Shopexlist.com | All rights Reserved | Sitemap

Shopexlist.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or one of its affiliates.